CompuSTAR DR-1000 Instruction Manual download pdf

830 N Milwaukee Ave Chicago, IL 60642 312-421-1114

Smartkey Starter®!

Basic Installation Instructions

The Smartkey Starter® is designed as a direct plug in interface to the rear of the Mercedes Benz key cylinder. Please

read this manual in it’s entirety prior to installation as there is a specific order of operation that needs to be followed.

Tools and Parts you will need

-T-20 driver

-T-25 driver

-Philips screwdriver

-10mm socket and ratchet

-Drill

-3/4” drill bit or Unibit

-Panel removal tool

-Mercedes Benz EIS removal tool p/n 639 589 01 07 00 (optional in most installations, but can make the job much

easier. This can be purchased from your local Mercedes dealer. Alternatively, we can provide you one with your

order). Also, we include this tool in our Smartkey Starter® Combo package which allows you to stock all parts

required to accommodate any Mercedes that we support in one simple kit.

Vehicle Diagrams available at http://www.smartkeystarter.com/service.htm

DO NOT MOUNT THE MODULE NEAR ANY HEAT SOURCES IN THE

VEHICLE. SPECIFIC LOCATIONS TO AVOID ARE THE HEATER CORE AND

THE TRANSMISSION TUNNEL.

Basic Installation

1. Gain access to the rear of the key cylinder (EIS).

2. Remove the plug(s) from the rear of the EIS that correspond to the harness to be installed.

3. Plug the T harness male plugs into the rear of the EIS.

4. Plug in the factory wiring removed in step 2 to the opposite side of the T harness.

5. Plug the Smartkey Starter® module into the end of the T harness.

6. If the vehicle has KeylessGo see KeylessGo connection section below

7. Turn on the Valet Switch.

8. Start the vehicle with the key and allow it to run for 1 full minute to verify all connections are properly locked in place

and there are no errors or warning lights.

9. Shut the vehicle off and push the panic button once to start the vehicle. Remotes lacking a panic button should use

“lock-unlock-lock” to activate the remote start sequence (see activation programming section below).

10.External lights will flash once to confirm receipt of start command and vehicle will start.

11.External lights will flash once every 5 seconds while vehicle is running.

12.Key take over

a. Standard vehicle -- insert key into ignition and turn to on position. Lights will flash (3) times and control will

automatically be transferred to the key and remote start will turn off.

b. KeylessGo vehicle -- push start button (1) time. Lights will flash (3) times and control will automatically be

transferred to the key and remote start will turn off.

13.Once all is confirmed working, shut down the vehicle.

14.Route the Valet switch to a convenient location under the dash.

15.Drill a 3/4” hole for mounting the valet switch.

16.Disconnect the wires from the switch and snap the valet switch into place.

17.Reconnect the wires and confirm starter operation once again prior to reassembling the vehicle.

1 2 3 4 5 6 ... 11 12

Summary of Contents

Page 1 - Smartkey Starter®!

830 N Milwaukee Ave Chicago, IL 60642 312-421-1114Smartkey Starter®!Basic Installat

Page 2 - Example Wiring Diagrams

SKS On Board KeylessGo Finder Instructions (sks v27.4 and up)Beginning with V27.4 (see serial number sticker on the rear of the SKS unit), there is an

Page 3 - For SKS-HS:

Compustar Programming InstructionsTo program any compatible Compustar remote control, complete the above installation steps and verify standard operat

Page 4 - Activation programming

Troubleshooting Diagnostic FlashesWhile running on remote start, any of the following will cause vehicle shut down−opening the hood (7 flashes)−d

Page 5 - Location chart

18.Mount the Smartkey Starter® module securely in the dash cavity away from any heat source (see previous warning) and tie up all harnessing neatly an

Page 6 - CAN connector

Smartkey Starter® V2.7 Jumper Adjustment up to V27.5*LeftRightLeftRightFor SKS-FT:Jumper Right -- 2010-2011 ML, GL, R Bluetec Diesel Jumper Left (pict

Page 7

2010-up E Class Sedan (W212) and 2012 CLS (W218) power wire connectionThe SKS204 harness covers the 2008-2010 C, 2010 GLK, 2010-up E class coupe and

Page 8 - KeylessGo Connection

KeylessGo Connection (not required for 2004-2009 E, 2004-2011 CLS, 2004-2009 CLK)Tools and Parts RequiredT-20 DriverPick ToolPanel Removal ToolDigital

Page 9

ML, GL, R Class KeylessGo ModuleCAN connector GL -- right rear side of cargo compartment R KeylessGo module -- under cargo area floor ML

Page 10

Keylessgo Module CAN connectorRight rear corner of trunk Under rear of driver’s seatS and CL (2011) C, E, and GLK KeylessG

Page 11

KeylessGo module behind bracket E Wagon -- right rear cargo area CAN connector, 2010-up E, C, GLK, 2012 CLS passenger front

Page 12

!Empty connector housing reinstalled!! ! Pins ready for new connector housing Brown/red matches to brown/redBrown matches to brownPins installed in co

CompuSTAR DR-1000 Instruction Manual

Browse online or download Instruction Manual for Mobile phones CompuSTAR DR-1000. CompuSTAR DR-1000 Programming instructions User Manual

Summary of Contents

More documents for Mobile phones CompuSTAR DR-1000

Comments to this Manuals